Or Book Technician Here

 

 

What're your insights and beliefs about Installing A Bathtub?

Setting up a bathtub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is conveniently obtainable, the job can move rapidly; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and set in the brand-new one. See to it you have actually qualified on your own for the work as well as are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed task, it is far better to think about employing one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you mount a new bathtub in your washroom if you have currently purchased a new bathtub as well as do not require to change the setup of your previous water system pipes.
Your devices as well as material list must comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Setup

Firstly, the sustaining framework provided with the bath should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.

 

 

Removing Old Touches

If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly bothersome because of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Making use of both wood boards under its feet, position the bath tub in the called for setting. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the tub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water system as well as check all joints and also brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the tub ought to wait till the bath tub has been used at the very least once as this will resolve it into its last position.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can split rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I'm certainly very excited about Installing A Bathtub and I'm hoping you enjoyed reading the entire page. In case you appreciated our post plz be sure to share it. Thanks so much for your time spent reading it.

Book